A magazine wants to improve their customer satisfaction. They surveyed some readers on their overall satisfaction as well as satisfaction with some quality aspects. Their basic question is“which aspects have most impact on customer satisfaction? ”We’ll try to answer this question with regression analysis. Overall satisfaction is our dependent variable (or criterion) and the quality aspects are our independent variables (or predictors).

The data have already been prepared and can be downloaded from magazine_reg.sav.

## Preliminary Settings

Our data contain a FILTER variable which we’ll switch on with the syntax below. We also want to see both variable names and labels in our output so we’ll set that as well.

***1. Switch filter variable on.**

filter by filt1.

***2. Show variable names and labels in output.**

set tvars both.

## SPSS ENTER Regression

We’ll first run a default linear regression on our data as shown by the screenshots below.

Note (below) that we usually select correlations on which our regression is based.

because it uses as many cases as possible for computing the

Clicking

results in the syntax below. We’ll run it right away.## SPSS ENTER Regression – Syntax

***Basic regression syntax. Note that “method=enter” in last line.**

REGRESSION

/MISSING PAIRWISE

/STATISTICS COEFF CI(99) OUTS R ANOVA COLLIN TOL

/CRITERIA=PIN(.05) POUT(.10)

/NOORIGIN

/DEPENDENT satov

/METHOD=ENTER sat1 sat2 sat3 sat4 sat5 sat6 sat7 sat8 sat9.

## SPSS ENTER Regression – Output

In our output, we first inspect our coefficients table as shown below.

Some things are going dreadfully wrong here:

The b coefficient of -0.075 suggests that *lower* “reliability of information” is associated with *higher*satisfaction. However, these variables have a positive correlation (r = 0.28 with a significance level of 0.000).

This weird b-coefficient is not statistically significant: there’s a 0.063 probability of finding this coefficient in our *sample* if it’s zero in the *population*. This goes for some other predictors as well.

This problem is known as **multicollinearity**: we entered too many intercorrelated predictors into our regression model. The (limited) R square gets smeared out over 9 predictors here. Therefore, the *unique* contributions of some predictors become so small that they can no longer be distinguished from zero.

The confidence intervals confirm this: it includes zero for three b-coefficients.

A rule of thumb is that Tolerance < 0.10 indicates multicollinearity. In our case, the **Tolerance statistic fails dramatically** in detecting multicollinearity which is clearly present. Our experience is that this is usually the case.

## Resolving Multicollinearity with Stepwise Regression

A method that almost always resolves multicollinearity is stepwise regression. We specify which predictors we’d *like to* include. SPSS then inspects which of these predictors really contribute to predicting our dependent variable and excludes those who don’t.

Like so, we usually end up with fewer predictors than we specify. However, those that remain tend to have solid, significant b-coefficients in the expected direction: *higher* scores on quality aspects are associated with *higher* scores on satisfaction. So let’s do it.

## SPSS Stepwise Regression – Syntax

We copy-paste our previous syntax and set `METHOD=STEPWISE`

in the last line. Like so, we end up with the syntax below. We’ll run it and explain the main results.

***Basic stepwise regression.**

REGRESSION

/MISSING PAIRWISE

/STATISTICS COEFF OUTS CI(99) R ANOVA

/CRITERIA=PIN(.05) POUT(.10)

/NOORIGIN

/DEPENDENT satov

/METHOD=stepwise sat1 sat2 sat3 sat4 sat5 sat6 sat7 sat8 sat9.

## SPSS Stepwise Regression – Variables Entered

This table illustrates the stepwise method: SPSS starts with zero predictors and then adds the strongest predictor, sat1, to the model if its b-coefficient in statistically significant (p < 0.05, see last column).

It then adds the second strongest predictor (sat3). Because doing so may render previously entered predictors not significant, SPSS may remove some of them -which doesn’t happen in this example.

This process continues until none of the excluded predictors contributes significantly to the included predictors. In our example, 6 out of 9 predictors are entered and none of those are removed.

## SPSS Stepwise Regression – Model Summary

SPSS built a model in 6 steps, each of which adds a predictor to the equation. While more predictors are added, **adjusted r-square levels off**: adding a second predictor to the first raises it with 0.087, but adding a sixth predictor to the previous 5 only results in a 0.012 point increase. There’s no point in adding more than 6 predictors.

Our final adjusted r-square is 0.39, which means that our 6 predictors account for 39% of the variance in overall satisfaction. This is somewhat disappointing but pretty normal in social science research.

## SPSS Stepwise Regression – Coefficients

In our coefficients table, we only look at our sixth and final model. Like we predicted, our b-coefficients are all significant and in logical directions. Because all predictors have identical (Likert) scales, we prefer interpreting the b-coefficients rather than the beta coefficients. Our final model states thatsatov’ = 3.744 + 0.173 sat1 + 0.168 sat3 + 0.179 sat5 + 0.150 sat7 + 0.128 sat9 + 0.110 sat4Our strongest predictor is sat5 (readability): a 1 point increase is associated with a 0.179 point increase in satov (overall satisfaction).

Our model doesn’t *prove* that this relation is causal but it seems reasonable that improving readability will cause slightly higher overall satisfaction with our magazine.